Show simple item record

Шахрай, С. Г.
Шарыпов, Н. А.
Поляков, П. В.
Кондратьев, В. В.
Карлина, А. И.
2019-07-01T07:30:01Z
2019-07-01T07:30:01Z
2017-10
Шахрай, С. Г. Quality of Anode. Overview of Problems and Some Methods of their Solution Part 2. Improving the quality of the anode [Текст] / С. Г. Шахрай, Н. А. Шарыпов, П. В. Поляков, В. В. Кондратьев, А. И. Карлина // International Journal of Applied Engineering Research. — 2017. — Volume 12 (Number 21). — С. pp. 11268-11278
http://www.ripublication.com/ijaer17/ijaerv12n21_105.pdf
http://elib.sfu-kras.ru/handle/2311/111482
Laboratory studies have shown that charging the components of the anode mass increases the rate of wetting and impregnation of dust by the pitch in 2-3 times, as evidenced by the shorter time interval during which the moistened coke was immersed in the pitch melt. The algorithm for obtaining anode mass according to the proposed technological scheme is the following. The components of coke batch - bunches of different fractional composition from bunkers 2 by metering devices 3 and transport screws 5 are fed to preheater 6 where they are heated to a temperature of 200-220 ° C. Further, the heated components of the coke batch are fed into the mixer 11. Coke dust before entering the mixer 11 by the dispenser 4 from the bunker 1 is fed into the dust preheater 9 where it is also heated to a temperature of 200-220 ° C. Pitch, preheated to a temperature of 200-2400C, is fed into the dispenser 8. Further heated coke dust and pitch enter high-voltage charging units 7, where they acquire electrical charges for 1-3 seconds, pitchnegative, and coke dust-positive. At the same time, the voltage at the electrodes of high-voltage charging stations is in the range of 24000-50000 V DC. Charged in this way, pitch and coke dust also enter mixer 11, where they are mixed for 3-4 minutes with each other and with coke batch. From the mixer 11, the finished anode mass is fed into the extruder 10 to form briquettes. In general, the process of anode preparation takes 4-5 minutes, which is 2 times lower than with "traditional" technology. The presented technology allows essentially to raise productivity of the manufacture equipment of an anode mass at the expense of time reduction of mixing more than in 2 times. Reducing the mixing time of components reduces the specific electricity consumption for anode production by 20-25 kW / t, taking into account the energy consumption of the high-voltage charging unit. An increase in the degree of impregnation of coke dust with pitch reduces the anode fall- off under the conditions of the active electrolyzer and reduces the yield of coal foam by 5-7 kg / ton of Al. Reducing the yield of coal foam reduces the time of the electrolyzer in the depressurized state by an average of 0.2-0.25 hours during the day, which reduces the specific fluoride emissions by 0.1-0.2 kg / ton Al.
aluminum electrolyzer
anode
carbon
coal foam
consumption
oxidation
protection
method
Quality of Anode. Overview of Problems and Some Methods of their Solution Part 2. Improving the quality of the anode
Journal Article
Journal Article Preprint
pp. 11268-11278
53.03
2019-07-01T07:30:01Z
Институт цветных металлов и материаловедения
Кафедра техносферной безопасности горного и металлургического производства
International Journal of Applied Engineering Research
Q3


Files in this item

Thumbnail

This item appears in the following Collection(s)

Show simple item record